A Statistical Prediction of Electrical Discharge Initiation and Semi-Analytical Transient Mixed Lubrication Model of a Rolling Element

2024-9-11

Triboinformatics approach for prediction of high-stress abrasive wear and coefficient of friction in Al/TiC nanocomposites using machine learning techniques

2024-9-11

High-speed 50,000 rpm planetary roller reducer for electric vehicles: Design and transmission efficiency analysis

2024-9-11

Evolution of lubrication characteristics of double-nut ball screws based on an efficient surface roughness modeling method

2024-9-10

Finite element simulations and statistical analysis for the tribological design of mutually textured surfaces and related experimental validation

2024-9-10

Effect of Entrainment Sliding Direction to the Traction Coefficient for Elastohydrodynamic Lubrication Elliptical Contacts in the Linear Isothermal Region

2024-8-30

Research on Wear Behavior Between Crossed Parabolic Cylinders in the Early Stage of Cyclic Fretting

2024-8-30

Static characteristics and dynamic coefficients of a gas-oil lubricated journal bearing under a pressurized refrigerant environment

2024-8-30

On the Study of Impact Plasto-Elastohydrodynamic Lubrication (PEHL) of Point Contact Problems Lubricated with non-Newtonian Lubricant

2024-8-30

Rapid Failure of Lubricated Contacts With Grease Under Zero Entraining Velocity Condition

2024-8-30

A Review on Mechanical and Wear Characteristics of Magnesium Metal Matrix Composites with Machine Learning Modelling

2024-8-30

Comparing the Cavitation and Slurry Erosion Wear Resistance of 16Cr-5Ni Stainless Steel with 13Cr-4Ni CA6NM Stainless Steel

2024-8-22

Optimization of Oil Bores on Connecting Rod Small End to Prevent Bushing Failures at Maximum Speed

2024-8-20

A Novel Method for Bearing Fault Diagnosis Based on Novel Feature Sets with Machine Learning Technique

2024-8-20

Factor Analysis-Based Selection of Xanthoceras Sorbifolia Bunge Oil as a Promising Bio-Based Lubricant

2024-8-20

The excellent anti-wear and friction-reducing performance of magnesium silicate hydroxide/graphite nanocomposite (MSH-C) as a lubricant additive

2024-8-20

Analysis of precision loss of double-nut ball screw considering dimensional error and preload degradation

2024-8-20

Probing the Synergy of Calcium Sulfonate Complex Soap and Polyurea Complex Thickener Towards Good Lubrication and Rheological Properties

2024-8-20

An Integrated Finite Element and ADAMS Modeling Approach for Analyzing Rotor-Bearing Housing Systems

2024-8-9

Heat Transfer in Squeeze-Film Flow between Rotating Disks

2024-8-9

Constituting and Investigation of Ion implanted Protective Layer on NiTi Alloy for Mechanical and Tribological Applications

2024-8-9

Influence of Elements in Steel With Anode Plasma Electrolytic Boriding on Hardness Gradient and Tribological Properties

2024-8-5

Influence of Heat Treatment on Fretting Wear Behavior of Laser Powder Bed Fusion Inconel 718 Alloy

2024-8-5

Effect of friction on critical cutting depth for ductile-brittle transition in material removal mechanism

2024-7-23

A Computational Design Framework for Lubrication Interfaces with Active Micro-Textures

2024-7-19

Topology optimization of the misaligned water-lubricated thrust bearings

2024-7-19

Air foil thrust and journal bearing coatings: A review

2024-7-16

Oil-soluble sulfur-containing organic molybdenum (SOM) as lubricant additives: a review

2024-7-16

Molecular structures, tribological properties and working mechanisms of sulfur- and phosphorus-free organic molybdenum (SPFMo) as additives in lubricants: a short review

2024-7-16

Study on internal load distribution of deep groove ball bearings considering raceway surface waviness

2024-7-16

In-vitro wear of Titanium reinforced Hydroxyapatite coatings in simulated body fluid

2024-7-16

A Review of Computational Fluid Dynamics Approaches Used to Investigate Lubrication of Rolling Element Bearings

2024-7-4

Effect of Thermal Conductivity on Maximum Film Pressure in Point EHL Contact of Ceramics with Transverse Surface Roughness

2024-7-2

Effect of variable load on centralized dimple in opposite sliding condition

2024-7-2

Numerical Calculation of the Oil Flow in a Truck Rear Axle Transmission and the Influence of Gear-Induced Air Flow

2024-7-2

Exploring the impact of HFO-1234YF refrigerant on the tribological properties of advanced polymeric coatings

2024-7-2

Tribute to Prof. Michael R. Lovell

2024-6-26

Understanding Electric Current Effects on Tribological Behaviors of Instantaneous Current-Carrying Pair with Recurrence Plot

2024-6-24

Improving signal transmission quality of wind turbine pitch slip ring with copper matrix composites

2024-6-24

Investigations on Tool Wear Behaviour of TiAlVN and TiAlN/TiAlVN Coated Tools in the Milling Inconel 718

2024-6-24

Combined Effect of Surface Irregularities and Applied Voltage on the Behavior of Hole-Entry Spherical Hybrid Journal Bearings Lubricated with an Electro-Rheological Fluid

2024-6-18

An analytical adhesion model for elastic contact electrification

2024-6-18

Modeling of double-row cylindrical roller bearing under combined loads and angular misalignment

2024-6-18

Effect of Cavity Shapes on the Lubrication Performance of High Precision Static and Dynamic Thrust Bearing under Eccentric Load

2024-6-13

Friction Variability in Slip Rings: Geometry and Stiffness Effects

2024-6-11

Effect of TiO2-SiC and heat treatment on tribological characteristics of bimodal hybrid aluminium composites under dry sliding condition

2024-6-7

Impact of oil supply conditions on water lubrication assisted with minimal secondary lubricating medium

2024-6-6

Ultrasound-assisted synthesis of novel undecylenic estolides: Modeling and Tribological characterization

2024-6-5

Point Contact Elastohydrodynamic Lubrication and Wear in Intermittent Motion

2024-6-4

Friction and wear of Ni alloy-Ag-Ni doped <i>h</i>BN self-lubricating composites from room temperature to 800 °C

2024-6-4