Use of Taguchi method for high energy ball milling of CaCO3

2022-2-4

Experimental investigation into the effect of surface roughness and mechanical properties of 3D-printed titanium Ti-64 ELI after heat treatment

2021-11-17

Injection-molded natural fiber-reinforced polymer composites–a review

2021-11-10

Effect of Non-Metallic Inclusion from the Continuous Casting Process on the Multi-Stage Forging Process and the Tensile Strength of the Bolt: A Case Study

2021-10-26

Plane wave in non-local semiconducting rotating media with Hall effect and three-phase lag fractional order heat transfer

2021-9-26

Microstructural and mechanical studies of feedstock material in continuous extrusion process

2021-9-6

CFD simulations of gearboxes: implementation of a mesh clustering algorithm for efficient simulations of complex system’s architectures

2021-8-5

Numerical model development to predict the behaviour of infant/neonate crash dummy restrained inside of an incubator under deceleration

2021-7-31

Prediction of buckling force in hourglass-shaped specimens

2021-6-29

Friction and contact temperature in dry rolling-sliding contacts with MoS2-bonded and a-C:H:Zr DLC coatings

2021-6-15

Effect of cone angle of cylindrical pin in the SFSW and DFSW on mechanical properties of AA6061-T6 alloy

2021-6-12

Development of calcium fluoride thin film on Ti-6Al-4V material by a dip coating process with an intermediate shellac layer for biocompatible orthopedic applications

2021-5-31

A Review on Process Parameters of Ti/Al Dissimilar Joint Using Laser Beam Welding

2021-5-5

Development of Impressive Tensile Properties of Hybrid Rolled Ta0.5Nb0.5Hf0.5ZrTi1.5 Refractory High Entropy Alloy

2021-5-3

Study of biaxial mechanical properties of the passive pig heart: material characterisation and categorisation of regional differences

2021-4-20

Experimental investigations and empirical relationship on the influence of innovative hub geometry in a centrifugal fan for performance augmentation

2021-3-19

Mathematical modeling of auxetic systems: bridging the gap between analytical models and observation

2021-3-17

Correction to: Memory-dependent derivative approach onmagneto-thermoelastic transversely isotropic medium with two temperatures

2021-2-7

Experimental investigation on a novel approach for laser surface hardening modelling

2021-1-13

Ductile failure analysis of epoxy resin plates containing multiple circular arc cracks by means of the equivalent material concept

2021-1-2

Memory-dependent derivative approach on magneto-thermoelastic transversely isotropic medium with two temperatures

2020-12-1

Interfacial assessment of degraded amorphous silicon module using scanning probe microscopy

2020-12-1

Simulation of Low Cycle Fatigue Behaviour of Nickel-Based Alloy at Elevated Temperatures

2020-10-3

Finite Element Modelling of a 3D Woven Composite for Automotive Applications

2020-10-1

Numerical Simulation on Deformation Behaviour of Additively Manufactured AlSi10Mg Alloy

2020-9-2

Retraction Note: Hydrothermal analysis on MHD squeezing nanofluid flow in parallel plates by analytical method

2020-8-28

Effects of Milling Process Parameters on Cutting Forces and Surface Roughness When Finishing Ti6al4v Produced by Electron Beam Melting

2020-7-1

Adomian’s Decomposition Method to Functionally Graded Thermoelastic Materials with Power Law

2020-7-1

Investigation of mechanical properties and surface roughness of friction stir welded AA6061-T651

2020-6-6

Evaluation of the Accuracy of Time of Arrival Source Location Algorithm of Acoustic Emission in Concrete-Mortar Structure

2020-6-1

Effects of tool offset, pin offset, and alloys position on maximum temperature in dissimilar FSW of AA6061 and AA5086

2020-5-15

Self-Organizing Map Network for Wheeled Robot Movement Optimization

2020-5-5

Finite Element Analysis of Thermally-Induced Bistable Plate Using Four Plate Elements

2020-4-5

The effect of alumina powder in dielectric on electrical discharge machining parameters of aluminum composite A413-Al2O3 by the Taguchi method, the signal-to-noise analysis and the total normalized quality loss

2020-4-3

Experimentation and numerical modeling on the response of woven glass/epoxy composite plate under blast impact loading

2020-2-10

Axisymmetric deformation in transversely isotropic magneto-thermoelastic solid with Green–Naghdi III due to inclined load

2020-1-31

Effect of concentration, aging, and annealing on sol gel ZnO and Al-doped ZnO thin films

2020-1-29

A novel to perform a thermoelastic analysis using digital image correlation and the boundary element method

2020-1-22

Modeling of Titanium Alloy Implant for Fractured Distal Femur

2020-1-4

An analytical investigation of elastic-plastic deformation of FGM hollow rotors under a high centrifugal effect

2019-12-1

Nonlinear pre and post-buckled analysis of curved beams using differential quadrature element method

2019-12-1

Investigation of a new methodology for the prediction of drawing force in deep drawing process with respect to dimensionless analysis

2019-11-28

A review of challenges and solutions in the preparation and use of magnetorheological fluids

2019-11-28

Rayleigh wave propagation in transversely isotropic magneto-thermoelastic medium with three-phase-lag heat transfer and diffusion

2019-10-16

Separation of Water/Organic Mixtures Using Micro- and Nanostructured Membranes of Special Type of Wettability

2019-10-2

Characterization of a Pure Diamond-Like Carbon Film Deposited by Nanosecond Pulsed Laser Deposition

2019-10-1

Characterization the effects of nanofluids and heating on flow in a baffled vertical channel

2019-9-18

Transversely isotropic thermoelastic thin circular plate with constant and periodically varying load and heat source

2019-8-23

The research design of graphene inclusion on LDPE characterization

2019-8-14

An Application of Path Planning Algorithms for Autonomous Inspection of Buried Pipes with Swarm Robots

2019-8-1