Research on the Correlation between Mechanical Seal Face Vibration and Stationary Ring Dynamic Behavior Characteristics

2024-9-12

Study on Temperature Field Distribution of a High-Speed Double-Helical Gear Pair with Oil Injection Lubrication

2024-9-9

Research on Polymer Wear under Water Conditions: A Review

2024-9-4

Running-In of DLC–Third Body or Transfer Film Formation

2024-9-4

The Generation and Evolution of High-Order Wheel Polygonal Wear from the Effects of Wheelset Rotation

2024-9-4

Premature Damage in Bearing Steel in Relation with Residual Stresses and Hydrogen Trapping

2024-9-3

Short-Term Influence of Water Ingress on Wear in Pitch Bearings of Wind Turbines

2024-9-2

Galling-Free Forging of Titanium Using Carbon-Supersaturated SiC Coating Dies

2024-9-1

Microstructure, Mechanical and Tribological Properties of Cu40Zn-Ti3AlC2 Composites by Powder Metallurgy

2024-8-31

Biomass-Derived Carbons as Friction Reducing Additives for Lubricants: Tribological Properties of Biochars and Activated Carbons Obtained from Sugar Cane Bagasse

2024-8-31

Evaluation of a Commercial MoS2 Dry Film Lubricant for Space Applications

2024-8-31

Moving beyond Flow Factors: Modeling Full Film Lubrication with Representative Surface Topography Using Heterogeneous Multiscale Methods

2024-8-30

Laboratory Test of a Gear Hydraulic Pump during the Application of an Environmentally Friendly Hydraulic Fluid with Constant Pressure and Temperature

2024-8-29

Changes in Surface Topography and Light Load Hardness in Thrust Bearings as a Reason for Tribo-Electric Loads

2024-8-28

Numerical Computation and Experimental Research for Dynamic Properties of Ultra-High-Speed Rotor System Supported by Helium Hydrostatic Gas Bearings

2024-8-27

A Comparison of the Tribological Properties of SiC Coatings Prepared via Atmospheric Plasma Spraying and Chemical Vapor Deposition for Carbon/Carbon Composites

2024-8-26

Plant-Based Oils for Sustainable Lubrication Solutions—Review

2024-8-26

Study on Traction Characteristics of Point Contact State under Oil–Air Lubrication

2024-8-25

Friction and Wear in Hot Stamping: The Role of Tool and Workpiece Temperature and Tool Steel Composition

2024-8-23

Dynamic Coefficient Investigation for Supercritical Carbon Dioxide Dry Gas Seal Based on Complete Variable Perturbation Model

2024-8-23

Molecular Dynamics Study on the Tribological Characteristics of Grain Boundary-Containing Graphene/h-BN Heterostructure Films

2024-8-22

The Improvement of CrN Coatings Wear Resistance by Adjusting the Cycle Number of Electrochemical

2024-8-20

A Fast Numerical Approach for Investigating Adhesion Strength in Fibrillar Structures: Impact of Buckling and Roughness

2024-8-19

Reliability-Based Robust Design Optimization with Fourth-Moment Method for Ball Bearing Wear

2024-8-19

Predicting Low Sliding Friction in Al-Steel Reciprocating Sliding Experiment after a Controlled Grinding of the Steel Counterface

2024-8-18

Process-Integrated Component Microtexturing for Tribologically Optimized Contacts Using the Example of the Cam Tappet—Numerical Design, Manufacturing, DLC-Coating and Experimental Analysis

2024-8-16

Material Optimization Method for a Spring-Energized Seal Based on Wear Analysis

2024-8-15

Machine-Learning-Based Wear Prediction in Journal Bearings under Start–Stop Conditions

2024-8-15

DSU-LSTM-Based Trend Prediction Method for Lubricating Oil

2024-8-15

Study on the Effect of Thermal Characteristics of Grease-Lubricated High-Speed Silicon Nitride Full Ceramic Ball Bearings in Motorized Spindles

2024-8-14

Influence of Lubrication Cycle Parameters on Hydrodynamic Linear Guides through Simultaneous Monitoring of Oil Film Pressure and Floating Heights

2024-8-14

Comparative Study on the Lubrication of Ti3C2TX MXene and Graphene Oxide Nanofluids for Titanium Alloys

2024-8-9

Theoretical and Experimental Study of Flexible Structure Tilting Pad Bearings Considering Deformation

2024-8-9

Study of Lubrication Performance and Churning Loss under Mixed Lubrication Mode in Gearbox

2024-8-8

Assessing Antioxidant and Pour Point Depressant Capacity of Turmeric Rhizome Extract in Biolubricants

2024-8-7

Optimization of Fused Filament Fabrication for High-Performance Polylactic Acid Parts under Wear Conditions

2024-8-6

The Target Detection of Wear Particles in Ferrographic Images Based on the Improved YOLOv8

2024-8-5

Effect of Grease Composition on Impact-Sliding Wear

2024-8-4

Enhancing the Tribological Properties of Bearing Surfaces in Hip Arthroplasty by Shot-Peening the Metal Surface

2024-8-3

Impact of Oil Viscosity on Emissions and Fuel Efficiency at High Altitudes: A Response Surface Methodology Analysis

2024-8-3

The Effect of Plastic Deformation on the Flattening of Friction Surfaces

2024-8-2

Revealing the Molecular Interaction between CTL Base Oil and Additives and Its Application in the Development of Gasoline Engine Oil

2024-7-31

Stability Analysis of the Secondary Motion of a Textured Piston

2024-7-31

Triboelectric Performance of Ionic Liquid, Synthetic, and Vegetable Oil-Based Polytetrafluoroethylene (PTFE) Greases

2024-7-30

Theoretical Model Development and Mixed Lubrication Analyses of Rolling Piston Type Rotary Compressors: A Review

2024-7-30

A Study on the Lubrication Characteristics and Parameter Influence of a High-Speed Train Herringbone Gearbox

2024-7-29

Investigation of Failure Mechanisms in Oil-Lubricated Rolling Bearings under Small Oscillating Movements: Experimental Results, Analysis and Comparison with Theoretical Models

2024-7-29

An Investigation of the Output Performances of a Triboelectric Nanogenerator Lubricated with TiO2-Doped Oleic Acid

2024-7-29

Exploring the Boundaries of Electrically Induced Bearing Damage in Grease-Lubricated Rolling Contacts

2024-7-28

Improved Tribological Properties of Epoxy Cement Reinforced with Impact-Resistant Core-Shell Structured Polymer Nanoparticles

2024-7-27