Advances in environmental research

Migration of leachate generated through embankment of construction waste soil (CWS) in low-lying areas was studied through physical and chemical analysis. A leachate solution containing soluble cations from CWS was found to have a pH above 9.0. To determine the distribution coefficients in the alkali solution, column and migration tests were conducted in the laboratory. The physical and chemical properties of CWS satisfied environmental soil criteria; however, the pH was high. The effective diffusion coefficients for CWS ions fell within the range of <TEX>$0.725-3.3{\times}10^{-6}cm^2/s$</TEX>. Properties of pore water and the amount of undissolved gas in pore water influenced advection-diffusion behavior. Contaminants migrating from CWS exhibited time-dependent concentration profiles and an advective component of transport. Thus, the transport equations for CWS contaminant concentrations satisfied the differential equations in accordance with Fick's 2nd law. Therefore, the migration of the contaminant plume when the landfilling CWS reaches water table can be predicted based on pH using the effective diffusion coefficient determined in a laboratory test.

Eunchul Shin

Jeongku Kang

Migration of calcium hydroxide compounds in construction waste soil

建筑垃圾土中氢氧化钙化合物的迁移

Four chickpea cultivars viz. kabuli (Pusa 1088 and Pusa 1053) and desi (Pusa 1103 and Pusa 547) differing in sensitivity to high temperature conditions were analyzed in earthern pot (30 cm) at different stages of growth and development in the year of 2010 and 2011. Pusa-1053 (kabuli type) showed maximum photosynthetic rate and least by Pusa-547 (desi type), whereas maximum cell membrane thermostability were recorded in Pusa-1103 and minimum in Pusa-1088. Among the treatments, the plants grown under elevated temperature conditions had produced 13.01% more significant data in comparison to plants grown under continuous natural conditions. Stomatal conductance were reduced 44.25% under elevated temperature conditions than natural conditions, whereas 35.56%, when plants grown under initially natural conditions upto 30DAS, then 30-60DAS elevated temperature and finally shifted to natural conditions till harvest. In case of Pusa-1103, stomatal conductance was maximum as compared to rest of 2.7% from Pusa-1053, 8.9% from Pusa-1088, and 10.3% in Pusa-547 throughout the study. Plants grown under continuous elevated temperature conditions had produced 15.30% and 15.32% more significant membrane thermostability index in comparison to continuous natural conditions at vegetative stage and 19.40% and 18.44% at flowering stage, while the better response was recorded at pod formation stage. Pusa-1053 had given 2.8% more membrane thermostability index than Pusa-1088 and Pusa-1103 had given 1.6% more membrane thermostability index than Pusa-547 in the present study. The membrane disruption caused by high temperature may alter water ion and inorganic solutes movement, photosynthesis and respiration. Thus, thermostability of the cell membrane depends on the degree of the electrolyte leakage.

Amit Kumar Jain

Heat sensitivity on physiological and biochemical traits in chickpea (Cicer arietinum)

鹰嘴豆（Cicer arietinum）生理和生化性状的热敏感性

Eight trace metals, Cd, Co, Cr, Cu, Mn, Ni, Pb and Zn, were measured in the urban soil of Guwahati City, Assam, India from 31 sites representing five different types of land use, residential, commercial, industrial, public utilities, and roadside. Cd and Co occurred in very low concentrations (Cd << Co) in all types of land use without any significant variation from one type of land use to another. Ni concentrations were more than those of Co, and the concentrations depended on land use pattern. Average Cr and Cu concentrations were ≥ 100 mg/kg, but Cr had a significantly higher presence in industrial land use. Pb concentrations showed similar trends. The two metals, Mn and Zn, were present in much larger amounts compared to the others with values ≥ 300 mg/kg. Industrial and roadside soil contained much more Mn while commercial soil was enriched with Zn. Toxicity Characteristic Leaching Procedure (TCLP) was used for elucidating the mobility characteristics of the eight heavy metals. Mn suffered the highest leaching from commercial land (9.9 mg/kg on average) and also from other types of land. Co, Cu and Pb showed higher leachability from commercial soils but the leached concentrations were less than those of Mn. The two metals, Zn and Ni, were leached from residential land in considerable amounts. The TCLP showed Mn to be the most leachable metal and Cr the least.

Krishna G. Bhattacharyya

Mayur J. Mahanta

Accumulation of Cd, Co, Cr, Cu, Mn, Ni, Pb and Zn in urban soil and their mobility characteristics

城市土壤中Cd、Co、Cr、Cu、Mn、Ni、Pb和Zn的积累及其迁移特性

In this study, we investigated a life cycle assessment (LCA) of six roof-waterproofing systems [asphalt (C1), synthetic polymer-based sheet (C2), improved asphalt (C3), liquid applied membrane (C4), Metal sheet with asphalt sheet (N1), and liquid applied membrane with asphalt sheet (N2)]for reinforced concrete building using an architectural model. To acquire accurate and realistic LCA results, minimum units of material compositions for life cycle inventory and real data for compositions of waterproofing materials were used. Considering only materials and energy demands for waterproofing systems per square meter, higher greenhouse gas (GHG) emissions could be generated in the order of C1 > N2 > C4 > N1 > C2 > C3 during construction phase. However, the order was changed to C1 > C4 > C3 > N2 > N1 > C2, when the actual architecture model was applied to the roof based on each specifications. When an entire life cycle including construction, maintenance, and deconstruction were considered, the amount of GHG emission was in the order of C4 > C1 > C3 > N2 > C2 > N1. Consequently, N1 was the most environmental-friendly waterproofing system producing the lowest GHG emission. GHG emissions from maintenance phase accounted for 71.4%~78.3% among whole life cycle.

Sukwon Ji

Daeseung Kyung

Woojin Lee

Life cycle assessment (LCA) of roof-waterproofing systems for reinforced concrete building

钢筋混凝土建筑屋面防水系统的生命周期评估(LCA)

The determination of the effectiveness of the immobilization of blasting dust (waste generated in galvanic activities) in cement matrix, as well of mechanical, physical and microstructural properties of concrete paving blocks produced with partial replacement of cement was the objective of this work. The results showed that blasting dust has high percentage of silica in the composition and very fine particle size, characteristics that qualify it for replacement of cement in manufacturing concrete blocks. The replacement of Portland cement by up to 5% residues did not cause a significant loss in compressive strength nor increase in water absorption of the blocks. Chemical tests indicated that there is no problem of leaching or solubilization of contaminants to the environment during the useful life of the concrete blocks, since the solidification/stabilization process led to the immobilization of waste in the cement mass. Therefore, the use of blasting dust in the manufacture of concrete paving blocks is promising, thus being not only an alternative for proper disposal of such waste as well as a possibility of saving raw materials used in the construction industry.

Juliana Guerra Sgorlon

Celia Regina Granhen Tavares

Janaina de Melo Franco

Production of concrete paving blocks using electroplating waste - Evaluation of concrete properties and solidification/stabilization of waste

利用电镀废料生产混凝土铺路块——混凝土性能评估及废料固化/稳定化

Assessment of seasonal changes in surface water quality is an important aspect for evaluating temporal variations of river pollution due to natural or anthropogenic inputs of point and non-point sources. In this study, surface water quality data for 15 physico-chemical parameters collected from 7 monitoring stations in a river during the years from 2014 to 2016 were analyzed. The principal component analysis technique was employed to evaluate the seasonal correlations of water quality parameters, while the principal factor analysis technique was used to extract the parameters that are most important in assessing seasonal variations of river water quality. Analysis shows that a parameter that is most important in contributing to water quality variation for one season may not be important for another season except alkalinity, which is always the most important parameters in contributing to water quality variations for all three seasons.

Chitta R. Mohanty

Saroj K. Nayak

Assessment of seasonal variations in water quality of Brahmani river using PCA

利用PCA评估Brahmani河水质的季节性变化

New technologies or improvement of the existing technologies are required to enhance the efficiency of removal of pollutants from wastewater. In this study we attempted to produce and test the activated carbon produced from the refused tea waste for the removal of dyes from wastewater. The objectives of this investigation were to produce activated carbon from refused tea waste by chemical activation, evaluate its performance for the removal of color produced from Acid Yellow 36, and the modeling of its dye removal with the kinetic study. The activation was performed in two steps namely carbonization at <TEX>$375{\pm}25^{\circ}C$</TEX> and chemical activation with HCl at <TEX>$800^{\circ}C$</TEX> under the absence of Oxygen. Adsorption isotherms and kinetic studies were performed with a textile dye, Acid Yellow 36, at different concentrations (20-80 mg/L). The maximum dye removal (~90%) observed at 80 mg/L dye concentration and it reduced at low dye concentrations. Maximum adsorption (71.97 mg/g) was recorded at 96 h at <TEX>$29{\pm}1^{\circ}C$</TEX>. Low pH increased the dye adsorption (pH=2; 78.27 mg/g) while adsorption reduced at high pH levels indicating that the competition occurs in between OH- ions and AY36 molecules for the adsorption sites in RTAC. The Langmuir isotherm model clearly explained the dye adsorption, favorably, by RTAC. Moreover, kinetic studied performed showed that the pseudo second order kinetic model clearly describes the dye adsorption. Based on the results obtained in this study, it can be concluded that RTAC can be used for the removal of textile dyes.

Somasiri Wijetunga

Chathurika DFA Gunasekara

Evaluation of refused tea waste activated carbon for color removal: Equilibrium and kinetic studies

废弃茶叶活性炭脱色效果评价：平衡与动力学研究

Mining activities play a significant role in environmental pollution by producing large amounts of tailings which comprise heavy metals. The impressive increase in mining activities in recent decades, due to their high influence on the industry of developing countries, duplicates the need for a substantial effort to develop and apply efficient measures of pollution control, mitigation, and abatement. In this study, our objective was to investigate the effect of simulation of the leachate, pH and inflow intensity of transport of <TEX>$Pb^{2+}$</TEX>, <TEX>$Zn^{2+}$</TEX>, and <TEX>$Cd^{2+}$</TEX> through Lakan lead and zinc plant tailings, in Iran, and to evaluate the modeling efficiency by comparing the modeling results and the results obtained from previous column studies. We used the HP1 model and the PHREEQC database to simulate metals transport through a saturated soil column during a 15 day time period. The simulations assumed local equilibrium. As expected, a lower pH and inflow intensity increased metal transport. The retardation of heavy metals followed the order <TEX>$Zn^{2+}$</TEX> > <TEX>$Pb^{2+}$</TEX> > <TEX>$Cd^{2+}$</TEX> and the removal concentrations of Cd, Pb, and Zn at the inflow intensity critical scenario, and Cd and Pb at inflow acidity critical scenario exceeded the allowable EPA and Iranian's 1053 standard thresholds. However, although the simulation results generally agreed well with the results of the column study, improvements are expected by using multi-dimensional models and a kinetic modeling approach for the reactions involved. The results of such investigations will be highly useful for designing preventative strategies to control reactive transport of hazardous metals and minimize their environmental effects.

Fatemeh Izadi Tameh

Gholamreza Asadollahfardi

Ahmad Khodadadi Darban

Mathematical model for reactive transport of heavy metals in soil column: Based on PHREEQC and HP1 simulators

土壤柱中重金属反应性迁移的数学模型：基于PHREEQC和HP1模拟器

This paper discussed plurality in urban governance in Nigeria and its implication on delivery of urban environmental services, with a focus on water supply, sanitation and solid waste disposal. Conceptually, it explained urban governance as the sum total of the ways of achieving an inclusive city and expressed the urban governance system of Nigeria based the legal framework set for them. The paper explored the environmental implications of urban governance in Nigeria. It concluded that urban governance has several implications on delivery of urban environmental services in Nigeria. The dualism in urban governance is a factor contributing towards inefficient delivery of environmental services such as water supply, sanitation and solid waste management in Nigeria. The paper recommended, among others, a constitutional reform that will guarantee efficient urban governance and delivery of environmental services in Nigeria.

Oluwole Daramola

Oluwaseun Olowoporoku

Plurality of urban governance in Nigeria and its implications on delivery of environmental services

尼日利亚城市治理的多样性及其对环境服务提供的影响

The use of Granular Activated Carbon (GAC) and naturally occurring silica (Sand) as filtration media in water and waste water treatment systems is very common. While GAC offers the additional functionality of being an "adsorptive" filter for dissolved organics it is also more expensive. In this paper we present an experimental evaluation of the performance of a bed of GAC for colloid removal and compare the same with that from an equivalent bed of Sand. The experiments are performed in an "intermittent" manner over extended time, to "simulate" performance over the life of the filter bed. The experiments were continued till a significant drop in water flow rate through the bed was observed. A novel "deposition" and "detachment" rate based transient mathematical model is developed. It is observed that the data from the experiments can be explained by the above model, for different aqueous phase electrolyte concentrations. The model "parameters", namely the "deposition" and "detachment" rates are evaluated for the 2 filter media studied. The model suggests that the significantly better performance of GAC in colloid filtration is probably due to significantly lower detachment of colloids from the same. While the "deposition" rates are higher for GAC, the "detachment" rates are significantly lower, which makes GAC more effective than sand for colloid removal by over an order of magnitude.

Jaideep Chatterjee

Shajahan A

Shailendra Pratap

Santosh Kumar Gupta

A comparative study of granular activated carbon and sand as water filtration media with estimation of model parameters

颗粒活性炭与砂作为水过滤介质的比较研究及模型参数估算

短名
Journal Impact	1.25
国际分区	ENGINEERING, ENVIRONMENTAL(Q4)

涉及主题	生物化学工程类有机化学生态学环境科学物理材料科学地质学废物管理地理物理化学量子力学冶金环境化学环境工程生物化学吸附计算机科学复合材料热力学
出版信息	出版商: ，出版周期: ，期刊类型: journal，开源期刊: 否
基本数据	创刊年份: ，原创研究文献占比: 100.00%，自引率:27.30%， Gold OA占比: 0.00%

Advances in environmental research

期刊引文格式

有 1 位以上作者的期刊

有 2 位作者的期刊

有 3 位作者的期刊

有 5 位以上作者的期刊

书籍引用格式

学位论文引用格式

网页引用格式

专利引用格式

手工熬夜修改参考文献？研飞自动匹配期刊，一键轻松成稿，支持 Word/WPS

投稿经验分享