Jurnal Tribologi

Amit R. Bhende

Gajanan K. Awari

Sachin P. Untawale

Jurnal tribologi

Comprehensive bearing condition monitoring algorithm for incipient fault detection using acoustic emission

用于早期故障检测的声发射综合轴承状态监测算法

N. Sapawe

S. Syahrullail

M.I. Izhan

Evaluation on the tribological properties of palm olein in different loads applied using pin-on-disk tribotester

不同载荷下棕榈油酸摩擦学性能的评价——使用销盘式摩擦测试仪

S Many studies have been undertaken with a view to using chemically modified vegetable oil as a bio-based lubricant. This research focused on tribological properties of trimethylolpropane (TMP) ester, which is derived from renewable resource. This TMP ester was produced from jatropha methyl ester; it is biodegradable and has high lubricity properties. Two different conditions of lubrication are being investigated: extreme pressure and anti-wear. It was found that the TMP ester (Jatropha) has better lubricity in terms of wear and friction compared to paraffin oil under extreme pressure conditions. TMP ester (Jatropha) has similar characteristics to fully formulated lubricant (FFL), in terms of the coefficient of friction (CoF). In terms of the anti-wear condition, TMP ester (Jatropha) has the lowest CoF; however it also has the high wear scar diameter. This is due to corrosion and chemical attack.

N.W.M. Zulkifli

H.H. Masjuki

M.A. Kalam

R. Yunus

S.S.N. Azman

Lubricity of bio-based lubricant derived from chemically modified jatropha methyl ester

化学改性麻风树甲酯基生物润滑油的润滑性

The aim of this study is to investigate the effect of load on the friction and wear properties of palm kernel activated carbon epoxy (PKAC-E) composite. The PKAC-E composite specimen was fabricated by hot compression molding method. Dry sliding test was performed by using a pin-on-disc tribometer at various load conditions with constant sliding speed and distance. The experimental results show that wear rate and friction coefficient of PKAC-E composite decreases with applied load. However, at higher load, friction coefficient increases slightly and remains almost invariant with applied load. In addition, some adhesive and abrasive wear types were identified on the worn surfaces. The main conclusion of this work is that PKAC-E composite show unique properties as solid lubricant at low load under unlubricated conditions.

K.W. Chua

M.F.B. Abdollah

N. Ismail

H. Amiruddin

Potential of palm kernel activated carbon epoxy (PKAC-E) composite as solid lubricant: Effect of load on friction and wear properties

棕榈核壳活性炭环氧树脂(PKAC-E)复合材料作为固体润滑剂的潜力：载荷对摩擦和磨损性能的影响

M.N. Syahirah

A.N. Farhanah

M.Z. Bahak

Friction and wear of bearing material under water contaminated compressor oi

水污染压缩机油下轴承材料的摩擦与磨损

Amos Thounaojam

Anil Kumar Birru

Bone machining: an analysis of machining parameters such as cutting speed, feed rate, and depth of cut using bovine bone

骨骼加工：利用牛骨分析切削速度、进给率和切削深度等加工参数

骨加工：利用牛骨对切削速度、进给率和切削深度等加工参数的分析

骨骼加工：利用牛骨对切削速度、进给率和切削深度等加工参数的分析

Abbreviation
Journal Impact	1.60
Quartiles(Global)	ENGINEERING, MECHANICAL(Q3)

ISSN	2289-7232
h-index	12

Publication Information	Publisher: Malaysian Tribology Society (Mytribos)，Publishing cycle: ，Journal Type: journal，Open Access Journals: Yes
Basic data	Year of publication: 2019，Proportion of original research papers: 95.00%，Self Citation Rate:18.80%， Gold OA Rate: 0.00%
Average review cycle	网友分享经验：12 Weeks

Jurnal Tribologi

Journal Citation Format

A journal article with 1 author

A journal article with 2 authors

A journal article with 3 authors

A journal article with 5 or more authors

Books Citation Format

Thesis Citation Format

Web sites Citation Format

Patent Citation Format

Staying up late manually editing references? ivySCI automatically matches journals and helps you generate references with a single click.

Share Submission Experience

Comprehensive bearing condition monitoring algorithm for incipient fault detection using acoustic emission

Evaluation on the tribological properties of palm olein in different loads applied using pin-on-disk tribotester

Lubricity of bio-based lubricant derived from chemically modified jatropha methyl ester

Potential of palm kernel activated carbon epoxy (PKAC-E) composite as solid lubricant: Effect of load on friction and wear properties

Friction and wear of bearing material under water contaminated compressor oi

Bone machining: an analysis of machining parameters such as cutting speed, feed rate, and depth of cut using bovine bone

Bone machining: an analysis of machining parameters such as cutting speed, feed rate, and depth of cut using bovine bone

Bone machining: an analysis of machining parameters such as cutting speed, feed rate, and depth of cut using bovine bone

Bone machining: an analysis of machining parameters such as cutting speed, feed rate, and depth of cut using bovine bone

Bone machining: an analysis of machining parameters such as cutting speed, feed rate, and depth of cut using bovine bone