Advances in Industrial and Manufacturing Engineering

Jordi Farjas

José Antonio González

Daniel Sánchez-Rodríguez

Norbert Blanco

Marc Gascons

Josep Costa

Analytical criterion to prevent thermal overshoot during dynamic curing of thick composite laminates.

防止厚复合材料层板动态固化过程中热过冲的分析准则

C. Ravasio

G. Pellegrini

Experimental investigation on micro-EDM hybrid drilling process

微细电火花复合钻削工艺的实验研究

Md Imran Hossain

Ola L.A. Harrysson

Mohammad Asaduzzaman Chowdhury

Nayem Hossain

Impact of Graphene Nanoparticles on DLP-Printed Parts' Mechanical Behavior

石墨烯纳米颗粒对DLP打印件力学性能的影响

The use of electron beam welding for dissimilar welding (DW) of commercially pure (CP) vanadium to Ti–6Al–4V has been investigated via ARCAM S12, an additive manufacturing powder-bed system. Investigations of bead-on-plate welds for Ti–6Al–4V were first conducted to identify the process parameters for full penetration welds with a minimum energy input of 37 mA at a traverse speed of 7 mm/s. Vanadium bead on plate welds produced a penetration of approximately 75%, which was enough to proceed onto DW experiments. Defect-free full penetration welds were produced. The DW weld zone microstructure revealed an elongated dendritic structure comprised of bulky βTi grains and a fine substructure of α' laths. Thermal imaging (TI) showed an increment in radiance temperature ahead of the melt pool, indicating that there is a minimum energy required before keyhole welding is present, confirming mathematical calculations. Mechanical characterisation finds a fair range of hardness across both base metals (BM), heat affected zones (HAZ) and fusion zones (FZ). With no yield plateau in tensile test curves, the material is confirmed to fail on the side with lower mechanical properties, i.e., vanadium, which draws a fair process window for dissimilar welding between Ti6Al4V and vanadium alloys.

Affaan Uthman Moosa

Everth Hernández-Nava

Mohanad Kadhim Mejbel

Iain Todd

The joining of CP-vanadium and Ti–6Al–4V using the Electron Beam Melting Additive Manufacturing method

电子束熔融增材制造方法连接CP-钒和Ti-6Al-4V

The use of Field Assisted Sintering Technology (FAST) is examined for the consolidation of an advanced Ni-based superalloy powder feedstock. FAST processed material was directly compared to a benchmark material prepared via hot isostatic pressing (HIP) where it was found that density, hardness values and microstructures were comparable. FAST enables the retainment of the prior particle grain morphology when using sintering dwell times ranging from 10 to 240 min. The application of dwell temperatures above the γ′ solvus of the alloy resulted in significant grain growth. Measured densities reveal that the applied load and dwell time used during sintering have minimal effect on the final density of the consolidated material. The crystallographic texture was also shown to be isotropic in FAST consolidated material. This study demonstrates that FAST is potentially a viable complementary and/or alternative processing route for consolidating Ni-based superalloy powders.

K. Marshall

P. Schillinger

N.S. Weston

M. Epler

M. Jackson

A parametric study of the microstructural evolution of an advanced Ni-based superalloy powder when consolidated using Field Assisted Sintering Technology, compared to a hot isostatic pressing benchmark

场辅助烧结技术与热等静压基准相比，对先进镍基高温合金粉末微观结构演变的参数化研究

Nikhil Vijay Jagtap

Niklas Reinisch

Rasul Abdusalamov

David Bailly

Mikhail Itskov

Modeling of equivalent strain in 2D cross-sections of open die forged components using neural networks

使用神经网络对开式模锻件二维截面等效应变的建模

Sunil Pathak

Ondřej Stránský

Jan Šmaus

Jaromír Kopeček

Jinoop Arackal Narayanan

Jan Kaufman

Libor Beránek

Marek Böhm

Jan Brajer

Tomáš Mocek

Influence on Micro-Geometry and Surface Characteristics of Laser Powder Bed Fusion Built 17-4 PH Miniature Spur Gears in Laser Shock Peening

激光冲击喷丸对激光粉末床熔融制造的17-4 PH微型直齿轮微几何和表面特性的影响

Abbreviation	Adv. Ind. Manuf. Eng.
Journal Impact	4.08
Quartiles(Global)	ENGINEERING, MANUFACTURING(Q2)

ISSN	2666-9129
h-index	12

Publication Information	Publisher: Elsevier B.V.，Publishing cycle: ，Journal Type: journal，Open Access Journals: Yes
Basic data	Year of publication: 2020，Proportion of original research papers: 0.00%，Self Citation Rate:2.60%， Gold OA Rate: 98.95%
Journal Fees	$1750Details
Average review cycle	网友分享经验：11 Weeks

Advances in Industrial and Manufacturing Engineering

Journal Citation Format

A journal article with 1 author

A journal article with 2 authors

A journal article with 3 authors

A journal article with 5 or more authors

Books Citation Format

Thesis Citation Format

Web sites Citation Format

Patent Citation Format

Staying up late manually editing references? ivySCI automatically matches journals and helps you generate references with a single click.

Share Submission Experience

Analytical criterion to prevent thermal overshoot during dynamic curing of thick composite laminates.

Experimental investigation on micro-EDM hybrid drilling process

Impact of Graphene Nanoparticles on DLP-Printed Parts' Mechanical Behavior

The joining of CP-vanadium and Ti–6Al–4V using the Electron Beam Melting Additive Manufacturing method

A parametric study of the microstructural evolution of an advanced Ni-based superalloy powder when consolidated using Field Assisted Sintering Technology, compared to a hot isostatic pressing benchmark

Analytical criterion to prevent thermal overshoot during dynamic curing of thick composite laminates.

Experimental investigation on micro-EDM hybrid drilling process

Impact of Graphene Nanoparticles on DLP-Printed Parts' Mechanical Behavior

Modeling of equivalent strain in 2D cross-sections of open die forged components using neural networks

Influence on Micro-Geometry and Surface Characteristics of Laser Powder Bed Fusion Built 17-4 PH Miniature Spur Gears in Laser Shock Peening